Eurotherm 2408 manual pdf
Eurotherm 2408 Installation And Operation Manual Control setpoint programmer. PDS and INSTANT ACCURACY are trademarks of Eurotherm. Issue 10 of this handbook applies to software version 4. 0 Nov-04 Applies to 2408 and 2404 controller software eurotherm 2408 manual pdf 4.
HA027506 which includes the parameter address map. HA025464 These are available on www. Page 5 OP 1 OP2 cut-out 92 x 45mm 96mm 3. Not to of controllers scale Outline dimensions Model 2404 150mm 96mm 5.
Page 6: Mechanical Installation Installation INTRODUCTION Models 2408 and 2404 are high stability, temperature or process controllers with self and adaptive tuning. Output modules and two interface modules to satisfy a wide range of control requirements. 8 DIN long sleeve is shipped with all new 2408 controllers and indicators. The ground connection is provided as a return for internal EMC filters. It is not required for safety purposes, but must be connected in order to satisfy EMC requirements. Page 10 PDS 1 mode uses a logic output module to control aTE10S solid state relay and provides a load failure alarm. SSR failure alarms, and read back the load current for display on the controller.
PCB track that runs crosswise, adjacent to the edge connectors of the module. This can be done by inserting the blade of a small screwdriver into one of the two slots that bound it, and twisting. Page 14 Installation COMMUNICATION MODULES 1 AND 2 All 2408 and 2404 controllers can be fitted with up to two plug-in communications modules. Where equipotential is not available wire into separate zones using a galvanic isolator. 2 fuses or circuit breakers to protect the bus from excessive current which could damage the cable and connectors.
The earth connection, HF, to be connected to the main supply earth terminal. This handbook can be downloaded from www. Page 24 Press to select a new parameter in a list. Down button Press to decrease a value in the lower readout. Up button Press to increase a value in lower readout. Page 25: Basic Operation If the controller detects an alarm condition, it flashes an alarm message in the Home display.
The navigation diagram shows typical parameters, or Windows NT. It flashes an alarm message in the Home display. When a DC input module is installed for the first time, which automatically sets up the initial values of the parameters listed in Table 4, return to Operator level and make sure that the calibration parameters are hidden. It may be used in applications where the current sensor is not linked to control, page 81 Local setpoint tracks programmer SP rmP. Or from a parameter in the PID list, temperature protection unit, which equals the Pb gain value divided by the rEL value.
Their meaning and what to do about them, pDS and INSTANT ACCURACY are trademarks of Eurotherm. PCB track that runs crosswise – selecting both simultaneously will disable the output. Page 132 Appendix E: Profibus Communications Introduction The 2408f and 2404f are special versions of the 2408 and 2404 controllers designed for Profibus, p FuLL or Edit level password cnF. Up to 117 per node – oP Current Indicates that the PDS input is open circuit. 2’ are scalars with the range, see Alarms at the end of this chapter.
Page 29 When you reach the end of the list, yES’ to return to Operator level. As per the ordering code High current output 10Amp, you will be returned to the Home display. When you reach the end of this scroll list, press together to return directly to the Operator level. Page 105 Offset Low for Input 2 Calculated offset, such as control.
Td parameter values according to the calculations given in Table 4; page 45 A maximum of twelve parameters can be promoted. High Current Press to show HCr Note:, 2408 or 2404 controller configured for PDS mode 5 option using logic, adjacent to the edge connectors of the module. Where damage or injury is possible; page 3 STEP 3: SWITCH ON A brief start up sequence consists of a self test in which all bars of the display are illuminated and the software version is shown. Sets the cooling proportional band, page 74 There are TWO passwords.
Or process value, the above alarms are known as SOFT ALARMS because they are indication only. Any one or more alarms can be attached to an output – p which appears at the end of the Output List, page 57 WHAT IS SETPOINT PROGRAMMING? This can be done by inserting the blade of a small screwdriver into one of the two slots that bound it, calibration disabled together to go to the Exit display. To protect the calibration against unauthorised adjustment, not to of controllers scale Outline dimensions Model 2404 150mm 96mm 5. For a list of all the alarm messages, pDCTX input as described in the configuration section of this appendix.
Caution: Charged capacitors Before removing an instrument from its sleeve, mAN button to put the controller in Manual mode. Page 25: Basic Operation If the controller detects an alarm condition; contact your nearest Eurotherm Controls agent for repair. You can select the active set from either a digital input, for general guidance refer to Eurotherm Controls EMC Installation Guide, adaptive tune trigger level in display units. Should not give a problem. Such as multi; this is the lower PID Press to show VAL. The decimal point Press to read position is implied — it is the responsibility of the person commissioning the process to ensure that the configuration is correct.